Briggs&Stratton uk | Briggs and Stratton Vertical 2-7 HP Engine Parts | Briggs and Stratton Vertical 2-7HP Overhead Valve OHV Engine Parts | Briggs and Stratton Europa Engine Spare Parts
The Briggs and Stratton Europa engine is overhead valve and has a plastic fuel tank/cover over the whole engine. This noticably slopes towards the front of the engine.Its model number begins 9977??If the parts you need are not listed, please use the link button at the bottom of this page.
OUT OF STOCK
Walk behind mower cover.Protects against most weather conditions.Fits walk behind mowers up to 22"Width 55cmLength 142cmHeight to handlebar 119cm
Repair manual for all single cylinder OHV engines other than Vanguard(Intek, Diamond, Europa etc.)For Vanguard engines order 272147Covers all you need to know!
Click for more Information
RC12YC Spark plug for all OHV enginesRe-Set Gap to .020" for Intek and DOV vertical crankshaft engines
16mm/19mm Spark plug box wrench for 992304 spark plug
Briggs and stratton Start Care oil change kit. Includes 2 x 0.6 litres of oil (one bottle for an oil change and the other for through season top ups), 100ml bottle of fuel fit additive and deep sided oil drain tray.
Briggs and Stratton Petrol additive for all 4 stroke and 2 stroke petrol enginesPrevents fuel deterioration during periods of non-use and generally aids engine efficiencyEssential for correct winter storage of lawnmowers etc.100 ml, treats 10 litres of fuel.
Oil drain pump kit. Includes vacuum pump, oil container, tubing etc.Allows draining oil without tipping machine.
Throttle control and cable to fit many applications1.35m long. End can be bent to suitNegative action(Control pushed to fast, shortens inner wire)
Throttle control and cable to fit many applications1.35m long. End can be bent to suitPositive action(Control pushed to fast, lengthens inner wire)
Clamp and screw, throttle cable
Air filter cartridge for Europa EngineApprox 9.5cm long x 5.5cm high
Pre filter for 497725S cartridge
Oil dipstick "O" ring seal for Quantum engines whose model number begins 12
Fuel cap for Quantum engines.Now replaced with 692046 below, please order that
Fuel cap for Quantum and Quantum Mk1 engines
Fuel tube for most applicationsSold in units of 20cm. Multiple purchases will be supplied in one total lengthUse with 710075 clamps.(sold seperately)
Plated fuel tube hose clamp Fits 11mm O/D fuel tube 395051
Black fuel tube clamp. Fits 12mm O/D fuel hose(Slightly smaller than 95162)
Green fuel tube clamp. Fits fuel tube over 12mm O/D(Slightly larger than 691038)
In line fuel shut off valve supplied with 2 x 95162 tube clamp
RPM tachometer to accurately set engine speedEasy to use and compact. Complete with instructions and walletSuits any engine
Carb overhaul kit for all Quantum enginesIncludes gaskets, seals, inlet needle and seat, idle mixture screw, welch plugs, float pin, shaft seals.Note- some very early Quantum Mk1 engines may have a different idle mixture screw not included.
Inlet valve needle & seat. For Europa engines.
Carburetor bowl gasket for all Quantum enginesApprox 48mm outside diameter
Fibre carburetor bowl lower seal washer for many enginesApprox 10mm inside diameter
Fibre carburetor bowl lower seal washer for many enginesApprox 9mm inside diameter
Choke return spring for Intek engine
Intake gasket for original Intek engine(exhaust on right as viewed from behind the engine)
1/4 inch diameter bolt for engine cowling, carb bracket etc. Also replaces 692198(approx 14mm long)
Screw 10-32 thread x 3/8" long (0.19" thread diapmeter - approx 4.8mm)Used in many places where a small short screw is required such as pressed steel muffler guards, covers and shields etc.
Complete rewind assembly, plastic pawl typeIncludes pulley, spring, pawls and rope pre-assembled and ready to bolt onIncludes screws and instructions for replacing riveted unitPlease note - If your starter has metal pawls, this is NOT its replacement. You will need to use the "send enquiry" form on the left
Recoil pulley & spring for Quantum engines that have a screw retainer and plastic pawls & plateApprox 13.5cm diameter
Starter pawls & retaining plate for Sprint, Classic and Quattro engines with later (499901) type starter pulleyParts Included - 2 x 281505S pawl, 692299 plate & 691855 friction spring
Recoil pulley & spring for older type Quantum(series 12) engines with metal pawlsApprox 13.5cm diameter
3.5mm diameter recoil rope for quantum engines.Approx 2.4m long whiteReplaces shorter rope 66734
Rope guide. Includes bolt and nut for fitting to handle
Rubber recoil grip with plastic insert suits engines where grip returns to the engine
Starter grip for machines with extended rope and grip retained up the handles
Cylinder head gasket
Rocker cover gasket for Europa engine
Breather/valve chest gasket for Europa engine
Briggs and Stratton Europa crankcase/sump gasket
399781S Lower oil seal, (sump side) for all Quantum engines
Upper oil seal (flywheel side)Approx 32mm outside diameter x 20mm inside diameter
Ignition spark testerTests the ignition system for efficiencyFor all engines
Spark plug terminal (493880S) and rubber elbow (66538S) to fit all side valve HT leads
Electronic ignition armature magneto coil for Europa engines(fitted in lieu of 802574)Please note that there has been a design change to this unit. The new one may not resemble your original exactly but is correct and will fit the engine
Stop wire. Approx 42cm long
Indak Ignition key set. Contains two keysFlat profile. (see pop up link below for shape) Fits most electric start machines
Click here for profile shape pop-up
0.5Amp D.C. Charging alternator used on most electric start Europa engines
Interlock micro switch for electric start engines with OPC control. (dead man's handle)
Flywheel puller for small enginesDistance between outer hole centres approx 40mmIf your engine has a square drive starter clutch holding down the flywheel, you will also require 690662 nut (see below)
Engine brake lockout link. Used to disable the brake where an engine is fitted to an application which does not use a mechanical emergency stop lever. NOT TO BE FITTED WHERE AN ENGINESTOP LEVER IS PRESENT.
Brake spring. For brake with hinged pad.Approx 50mm long x 12mm diameter
Flywheel key to fit most enginesApprox. 14mm long x 3mm x 4mm
Half moon woodruff key to fit crankshaft extension of most small Briggs and Stratton engines applicationsNo 505 - 5/32" x 5/8" (approx 4mm thick x 15mm long)
#605 Woodruff Key 3/16" x 5/8" used on 25mm diameter crankshaft engines
Key, crankshaft pulley 3/16" (Approx 4.75mm) square section x 37mm long
Engine mounting bolt. Self tap 3/8" x 1". Suitable for mounting engine onto steel or alluminium chassis up to 1/4" thickness.